FT-736R (see *1), FT-747GX, FT-891, FT-991, FT-3000
Available CAT Definition Files, ONLY for VQLog 3.1 (build 53) or later:
Yaesu:
FT-450, FT-890, FT-900, FT-950, FT-1000 , FT-2000, FT-DX5000MP , FT-DX9000, FT-DX1200
Available CAT Definition Files for VQLog 3.0 and 3.1 (any build):
Kenwood:
R-5000, TS-50 , TS-140S , TS-440, TS-450, TS-480, TS-570D, TS-570S, TS-590S, TS-590SG , TS-690, TS-711, TS-790, TS-811, TS-850, TS-870S, TS-890S , TS-930, TS-940, TS-950, TS-950SDX, TS-990, TS-2000
Icom with CI-V Transceive=ON (recommended):
IC-271 , IC-275, IC-575, IC-703, IC-706, IC-706MKII, IC-706MKIIG, IC-718, IC-725, IC-728, IC-729, IC-735, IC-736, IC-737, IC-738, IC-746, IC-746PRO, IC-751A, IC-756, IC-756PRO, IC-756PROII, IC-756PROIII, IC-761, IC-775, IC-775DSP, IC-820, IC-821, IC-910H, IC-970 (A/E/H), IC-7000, IC-7100 , IC-7200, IC-7300, IC-7400, IC-7410, IC-7600 , IC-7610 , IC-7700, IC-7800, IC-7850, IC-7851, IC-9100 , IC-9700, IC-R10
Icom with CI-V Transceive=OFF:
IC-271, IC-275, IC-575, IC-703, IC-706, IC-706MKII, IC-706MKIIG, IC-718, IC-725, IC-728, IC-729, IC-735, IC-736, IC-737, IC-738, IC-746, IC-746PRO, IC-751A, IC-756, IC-756PRO, IC-756PROII, IC-756PROIII, IC-761, IC-775, IC-775DSP, IC-820, IC-821, IC-910H, IC-970 (A/E/H), IC-7000, IC-7100 , IC-7200, IC-7300, IC-7400, IC-7410, IC-7600, IC-7610 , IC-7700, IC-7800, IC-7850, IC-7851, IC-9100 , IC-9700, IC-R10
Yaesu:
FT-817, FT-847, FT-857, FT-897, FT-920, FT-990, FT-1000MP, FT-1000MP Mark-V
Elecraft:
K2, K3
FlexRadio:
Using PowerSDR with any SDR FlexRadio rig (See the FAQ page for detailed information)
Ten Tec:
Omni VI plus (See the FAQ page for detailed information)
Copyright notice: These CDF files are intended to be used only with VQLog program. Their direct or indirect use in other programs or the extraction of their contents for other purposes is strictly forbidden and will be prosecuted.
How to use these CDF?
Download the file corresponding to your rig, by clicking on its link above.
Unzip it and place the extracted .MDB file into the CAT subfolder of VQLog in your hard disk.
Run VQLog, go to 'Configuration - Rig control (CAT)' and select it in the 'Parameter file' list box.
Make sure you have read and understood how to configure CAT in VQLog.
If you are a registered user and need a CDF for other rigs please contact VQLog's support and I will do my best to develop it in a short time, but please read the following considerations first:
CAT implementation made by Kenwood is simple and powerful, with little or none differences between rigs. Thus creating a CDF for a Kenwood rig not listed above should not be a big problem.
The CAT implementation made by Icom makes use of the CI-V interface that is available in almost all modern rigs. It's also more or less common to all Icom rigs, but not so powerful as Kenwood's. Anyway creating a CDF for an Icom rig not listed above should also be easy.
I like Yaesu rigs a lot, but I have to say that their implementation of CAT is nothing but a bad joke for software developers. Almost each model has it's own version of the CAT protocol that has nothing to do with the version of other models. This means that supporting a rig not listed above could mean not only creating a CDF file, but recoding a lot in the program. I can't guarantee that a certain model of Yaesu will be supported by this version of the program.
Connection of the Elecraft K2 is possible through the accessory KIO2 RS-232 Interface, as its CAT implementation is compatible with Kenwood TS-570.
Also, if you notice some wrong behaviour in the CDF of your rig then contact VQLog's supportwith detailed information on the problem.
(*1) The FT-736R does not allow bidirectional communications. Once the CAT system is enabled you can only control the rig from the computer. The tuning knob and other buttons of the rig are blocked. This is the way Yaesu implemented the CAT in this rig.
Share: | Home page | Site map | Radio Sherlock search engine | Terms of service | Privacy | Cookies |
2 user comments
You should contact support using http://contact.vqlog.com
please configuration
cat for yaesu ft 5000
tanks
Add your public comment to this page.(Important: Only respectful comments directly related to the content of this page will be accepted here. Inquires and complains must be sent to the webmaster.)